
Verdict first: nothing on this page is a QuickJack, and anyone telling you otherwise is selling something. What a QuickJack sells is three things at once - height, both ends of the car at the same time, and about 30 seconds of setup. If you want the height, a pair of 6-ton Torin T46002A stands reaches 23-13/16 in for a tiny fraction of the outlay, raised by a jack like the Arcan A20019. If you want the drive-on speed, VEVOR ramps give you 6.7 in in seconds. The budget pick is the 3-ton T43002A: the cheapest way to hold a car safely at a working height. If you want all three things in one product, buy the QuickJack - we do not sell it and we earn nothing for saying so.
Matching it on height
This is the easiest of the three to replicate. A pair of 6-ton stands published at 15-3/8 in to 23-13/16 in covers the 17.5 in and 21 in figures QuickJack quotes, and costs less than a rounding error on a lift. The catch is the other end of the range: 15-3/8 in is the minimum, which is too tall to slide under most cars, so these are a truck and SUV answer. On a car you are working with 3-ton stands topping out near 16-3/4 in, which is below a QuickJack at full height but is still a working height for most jobs under a vehicle.
The other half of matching the height is the jack. You have to raise the car past the notch before you lower it on, so the jack's maximum lift has to beat your stand setting - and almost nothing reaches 23-13/16 in. Best high-lift floor jacks lists the few that come close, and how high does a floor jack lift does the clearance sum.
Matching it on both ends at once
You cannot, with stands, without four of them and two lifts of the car - which is a real procedure, not a stunt, but it is slow and it doubles the number of things that have to be set correctly. How many jack stands do I need covers how to do it properly. This is the QuickJack's genuine structural advantage: two frames under the pinch welds raise the whole car level in one motion, and nothing in this list does that.
Matching it on speed
Ramps are the answer, and they are faster than a lift. VEVOR publishes a 6.7 in lift height on a 17 degree incline at 16,000 lb GVW per pair; the setup is to put them in front of the wheels and drive. What you buy is access for a drain plug, a filter, an exhaust inspection or a transmission pan - and what you give up is any job that takes a wheel off, because the wheels are what the car is standing on. Car ramps vs jack stands is the comparison in full, and do I need jack stands with ramps answers the question people ask next.
The alternatives against the published QuickJack figures
| Option | Published height | Both ends at once | Setup |
|---|---|---|---|
| QuickJack BL-3500SLX | 17.5 in (21 in stacked) | Yes | Frames, power unit, hoses |
| QuickJack 6000TL | 21 in (24 in stacked) | Yes | Frames, power unit, hoses |
| Torin T46002A (6 ton stands) | 15-3/8 - 23-13/16 in | Only with four stands | Jack, then lower onto stands |
| Torin T43002A (3 ton stands) | 11-1/4 - 16-3/4 in | Only with four stands | Jack, then lower onto stands |
| Powerbuilt 620471 Unijack | 11 - 21 in | No - one corner | Pump, then set the locking bar |
| VEVOR service ramps | 6.7 in | One axle | Drive on |
Read the last two columns together. The cheap options match the height column and lose the other two, which is the honest summary of this entire page.
Who should still buy the QuickJack
Anyone who lifts a car often enough that setup time is the real cost - a track-day car, a project car, a household with four vehicles. Anyone whose garage floor is level concrete with room for 62.5 in or 70 in frames and somewhere to store them flat. And anyone who needs the whole car level, both ends up, for alignment-adjacent or exhaust work. Those are real reasons and the alternatives here do not meet them. We have no affiliate relationship with QuickJack and nothing to gain from recommending it; we also think most first garages are better served by a jack, two stands and a pair of ramps, which costs far less and covers more situations.
Jack stands vs QuickJack is the head-to-head comparison if you want the trade examined rather than the substitutes listed.
What we would buy
For a first garage replacing the idea of a lift: the Arcan A20019 jack plus a pair of T43002A stands, and a pair of VEVOR ramps for oil changes. That covers every job a home mechanic actually does, fits in a corner, and follows you to a friend's driveway. If the vehicle is a truck and the height is the point, swap the stands for the 6-ton T46002A and make sure the jack can reach past the notch. If you want one tool that lifts and holds a single corner, the Powerbuilt Unijack is the closest thing here - not a replacement for a pair of stands.



