
Short answer: the Torin BIG RED T43002A for most cars - ratchet plus safety pin, 11-1/4 in to 16-3/4 in, well inside the cap. If you want the best documented testing in the band, the ESCO 10498 publishes A2LA-certified ASME testing and 3 ton per stand. The budget pick is the T42002A, the cheapest pair here, which also starts the lowest at 10.8 in and carries the clearest standards wording on the page. For a truck, a pair of 6-ton T46002A stands still comes in under a hundred dollars.
What we judged these on
1. How many mechanisms hold the load
Three of the four sets here publish two independent locks: Torin states a ratchet bar plus a safety pin on the T43002A and T46002A, and a 10-level ratchet support bar plus a double locking pin on the T42002A. ESCO publishes a single pin with 10 positions - one mechanism, but one with no pawl to wear and no teeth to skip. There is no set in this band that asks you to trust a bare ratchet with nothing behind it, which is the main reason a $100 cap costs you nothing on safety.
2. What the standards claim actually says
US jack stands fall under ASME PASE, and the wording of the claim is the signal. "Complies with ASME PASE-2019" on the T42002A names an edition. "Tested to ASME standards by an A2LA-certified facility" on the ESCO names the lab's accreditation. "Meets ASME safety standards" on the T43002A and "tested to meet ASME standards" on the T46002A assert compliance without naming either. All four are claims by the maker; none of them is a test we ran.
3. Per pair or per stand - the trap on every listing
Torin quotes 3 ton (6,000 lb) per pair on the T43002A, which is 3,000 lb a stand. ESCO quotes 3 ton per stand, which is twice the figure for the same words. Both are generous under one corner of a car, because a corner of a typical sedan carries somewhere around a thousand pounds. On a heavy truck the difference stops being academic. Jack stand weight ratings takes it apart.
4. The height range, against your car and your jack
The published minimums in this band run 10.8 in, 11-1/4 in, 13.2 in and 15-3/8 in, and the difference decides whether the stand goes under your sill at all. The maximum matters for the other half of the sum: your jack has to raise the car past the notch you intend to use. A 14 in jack cannot serve a stand set at 16-3/4 in, and nothing under 24 in of lift can serve the 6-ton set at the top of its range. What size jack stands do I need works it through, and best floor jacks under $100 is the matching budget page for the lifting half.
The band on published figures
| Stand | Mechanism | Height range | Rating basis | Standards claim |
|---|---|---|---|---|
| Torin T43002A (3 ton) | Ratchet + safety pin | 11-1/4 - 16-3/4 in | Per pair | Meets ASME |
| ESCO 10498 (3 ton) | Pin, 10 positions | 13.2 - 21.5 in | Per stand | ASME testing, A2LA lab |
| Torin T46002A (6 ton) | Ratchet + safety pin | 15-3/8 - 23-13/16 in | Per pair | Tested to meet ASME |
| Torin T42002A (2 ton) | Ratchet + double locking pin | 10.8 - 16.5 in | Per stand | ASME PASE-2019 |
Every row in that table is inside the cap. There is no column where spending more than a hundred dollars would have bought a different kind of answer - the stands above this band buy finer increments and a US-made frame, not a second lock or a better standard.
What a hundred dollars does not buy
Finer height increments, mostly. Hein-Werner publishes 11/16 in steps on the HW93503, the finest we cover, and that set sits above this cap - fine steps are what let you match two stands exactly rather than closely. Best ratcheting jack stands ranks the field on that mechanism. It also does not buy a US-made frame, a lifetime warranty, or a saddle designed around a specific car's sill. None of those are safety items, which is the point of this page.
What the cap does cost you is the temptation to spend the whole hundred on stands. Don't: a pair of stands plus pads plus chocks is a better hundred dollars than a nicer pair of stands on their own, because the two failures that hurt people are a stand placed on the wrong part of the car and a car that rolls. Wheel chocks guide covers the second.
What we would buy
For a normal car: the T43002A, plus a set of slotted rubber pads, which together still leave change inside the cap. For a low car or the tightest budget: the T42002A, which starts at 10.8 in and names ASME PASE-2019. If independently accredited testing is what reassures you: the ESCO 10498. For a truck: the 6-ton T46002A, and check that your jack can reach past the notch you intend to use before you order.



